[PDF&VCE] Free Lead2pass 200-105 PDF Download 100% Pass Exam 200-105 (71-90)

2016 September Cisco Official New Released 200-105 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

We at Lead2pass are committed to help you clear your 200-105 certification test with high scores. The chances of you failing to clear your 200-105 test, after going through our comprehensive exam dumps is very bleak.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-105.html

Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

A.    802.1Q native VLAN frames are untagged by default.
B.    802.1Q trunking ports can also be secure ports.
C.    802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D.    802.1Q trunks require full-duplex, point-to-point connectivity.
E.    802.1Q trunks should have native VLANs that are the same at both ends.

Answer: ACE
To be the feasible successor, the Advertised Distance (AD) of that route must be less than the Feasible Distance (FD) of the successor. From the output of the "show ip eigrp topology we learn that the FD of the successor is 41152000. Now we will mention about the answers, in the "Composite metric is (…/…)" statement the first parameter is the FD while the second parameter is the AD of that route. So we need to find out which route has the second parameter (AD) less than 41152000 -> only answer B satisfies this requirement with an AD of 128256.
CCNA Self-Study (ICND Exam): Extending Switched Networks with Virtual LANs

Which two options are valid WAN connectivity methods? (Choose two.)

A.    PPP
B.    WAP
C.    DSL
D.    L2TPv3
E.    Ethernet

Answer: AC
On each WAN connection, data is encapsulated into frames before itcrosses the WAN link. The following are typical WAN protocols:1. High-level Data Link Control (HDLC): The Cisco default encapsulation type onpoint-to-point connections, dedicated links, and circuit- switches connections.2. PPP: Provides router-to-router and host-to-network connections over synchronous andasynchronous circuits. PPP was designed to work with several network layer protocols,including IP.3. Frame-relay: A successor to X.25. This protocol is an industry-standard, switchesdata-link layer protocol that handles multiple virtual circuits

Refer to the exhibit.
Which WAN protocol is being used?

A.    ATM
B.    HDLC
C.    Frame Relay
D.    PPP

Answer: C
"Show interface pos8/0/0" command showing LMI enq sent which show frame-relay encapsulation enabled on this interface . Cisco supports three different Local Management Interface (LMI) types for Frame Relay: Cisco, ANSI Annex D, and Q933-A Annex A http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=3

What occurs on a Frame Relay network when the CIR is exceeded?

A.    All TCP traffic is marked discard eligible.
B.    All UDP traffic is marked discard eligible and a BECN is sent.
C.    All TCP traffic is marked discard eligible and a BECN is sent.
D.    All traffic exceeding the CIR is marked discard eligible.

Answer: D
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are marked as discard eligible (DE) which means they can be dropped if the congestion occurs within the Frame Relay network.
Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit that is used to identify frames that are first to be dropped when the CIR is exceeded.

What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)

A.    They create split-horizon issues.
B.    They require a unique subnet within a routing domain.
C.    They emulate leased lines.
D.    They are ideal for full-mesh topologies.
E.    They require the use of NBMA options when using OSPF.

Answer: BC
Configuring Frame Relay Subinterfaces
On partially meshed Frame Relay networks, the problem of split horizon can be overcome by using Frame Relay subinterfaces. Frame Relay provides a mechanism to allow a physical interface to be partitioned into multiple virtual interfaces. In a similar way, using subinterfaces allows a partially meshed network to be divided into a number of smaller, fully meshed point-to-point networks. Generally, each point-to-point subnetwork is assigned a unique network address. This allows packets received on one physical interface to be sent out from the same physical interface, albeit forwarded on VCs in different subinterfaces.
There are two types of subinterfaces supported by Cisco routers: point-to-point and multipoint subinterfaces.

Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two.)

A.    CHAP uses a two-way handshake.
B.    CHAP uses a three-way handshake.
C.    CHAP authentication periodically occurs after link establishment.
D.    CHAP authentication passwords are sent in plaintext.
E.    CHAP authentication is performed only upon link establishment.
F.    CHAP has no protection from playback attacks.

Answer: BC
Understanding and Configuring PPP CHAP Authentication http://www.cisco.com/en/US/tech/tk713/tk507/technologies_tech_note09186a00800b4131.shtml
One-Way and Two-Way Authentication
CHAP is defined as a one-way authentication method. However, you use CHAP in both directions to create a two-way authentication. Hence, with two-way CHAP, a separate three-way handshake is initiated by each side. In the Cisco CHAP implementation, by default, the called party must authenticate the calling party (unless authentication is completely turned off). Therefore, a one-way authentication initiated by the called party is the minimum possible authentication. However, the calling party can also verify the identity of the called party, and this results in a two-way authentication. One-way authentication is often required when you connect to non-Cisco devices.

Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link?

A.    show frame-relay lmi
B.    show frame-relay map
C.    show frame-relay pvc
D.    show interfaces serial

Answer: B
map will show frame relay encapsulation (cisco or ietf) http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp1029343
show frame-relay map" will show frame relay encapsulation type (CISCO or IETF)

What is the purpose of Inverse ARP?

A.    to map a known IP address to a MAC address
B.    to map a known DLCI to a MAC address
C.    to map a known MAC address to an IP address
D.    to map a known DLCI to an IP address
E.    to map a known IP address to a SPID
F.    to map a known SPID to a MAC address

Answer: D
Frame-Relay (a Layer 2 protocol) uses Inverse-Arp to map a know Layer 2 Address (DLCI) to a unknow Layer 3 Address.
Dynamic Mapping
Dynamic address mapping relies on the Frame Relay Inverse Address Resolution Protocol (Inverse ARP), defined by RFC 1293, to resolve a next hop network protocol address to a local DLCI value. The Frame Relay router sends out Inverse ARP requests on its Frame Relay PVC to discover the protocol address of the remote device connected to the Frame Relay network. The responses to the Inverse ARP requests are used to populate an address-to-DLCI mapping table on the Frame Relay router or access server. The router builds and maintains this address-to-DLCImapping table, which contains all resolved Inverse ARP requests, including both dynamic and static mapping entries.
When data needs to be transmitted to a remote destination address, the router performs a lookup on its routing table to determine whether a route to that destination address exists and the next hop address or directly connected interface to use in order to reach that destination. Subsequently, the router consults its address-to-DLCI mapping table for the local DLCI that corresponds to the next hop address. Finally, the router places the frames targeted to the remote destination on its identified outgoing local DLCI.
On Cisco routers, dynamic Inverse ARP is enabled by default for all network layer protocols enabled on the physical interface. Packets are not sent out for network layer protocols that are not enabled on the physical interface. For example, no dynamic Inverse ARP resolution is performed for IPX if ipx routing is not enabled globally and there is no active IPX address assigned to the interface. Because dynamic Inverse ARP is enabled by default, no additional Cisco IOS command is required to enable it on an interface.
Example 4-16 shows the output of the show frame-relay map privileged EXEC mode command. The addressto-DLCI mapping table displays useful information. The output of the command shows that the next hop address is dynamically mapped to the local DLCI 102, broadcast is enabled on the interface, and the interface’s status is currently active.
After enabling Frame Relay on the interface, the Cisco router does not perform Inverse ARP until IP routing is enabled on the router. By default, IP routing is enabled on a Cisco router. If IP routing has been turned off, enable IP routing with the ip routing command in the global configuration mode. After IP routing is enabled, the router performs Inverse ARP and begins populating the address-to-DLCI mapping table with resolved entries.

Refer to the exhibit. A network associate has configured OSPF with the command:
City(config-router)# network area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)

A.    FastEthernet0 /0
B.    FastEthernet0 /1
C.    Serial0/0
D.    Serial0/1.102
E.    Serial0/1.103
F.    Serial0/1.104

Answer: BCD
The "network equals to network This network has: Increment: 64 (/26= 1111 1111.1111 1111.1111 1111.1100 0000)Network address:
Broadcast address: all interface in the range of this network will join OSPF – B C D are correct.

Refer to the exhibit. The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router.
Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?

A. is subnetted, 1 subnets
D [90/20514560] via, 6w0d, Serial0/1
B. is subnetted, 1 subnets
D [90/20514560] via, 6w0d, Serial0/1
C. is subnetted, 1 subnets
D [90/20514560] via, 6w0d, Serial0/1
D. is subnetted, 1 subnets
D [90/20514560] via, 6w0d, Serial0/1
E. is subnetted, 1 subnets
D [90/20514560] via, 6w0d, Serial0/1
F. is subnetted, 1 subnets
D [90/20514560] via, 6w0d, Serial0/1

Answer: D
All the above networks can be summarized to network but the question requires to "represent the LANs in Phoenix but no additional subnets" so we must summarized to network. The Phoenix router has 4 subnets so we need to "move left" 2 bits of "/24-> /22 is the best choice – D is correct.

What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)

A.    hello packets
B.    SAP messages sent by other routers
C.    LSAs from other routers
D.    beacons received on point-to-point links
E.    routing tables received from other link-state routers
F.    TTL packets from designated routers

Answer: AC

Which commands are required to properly configure a router to run OSPF and to add network to OSPF area 0? (Choose two.)

A.    Router(config)# router ospf 0
B.    Router(config)# router ospf 1
C.    Router(config)# router ospf area 0
D.    Router(config-router)# network 0
E.    Router(config-router)# network area 0
F.    Router(config-router)# network area 0

Answer: BE
In the router ospf
command, theranges from 1 to 65535 so o is an invalid number – B is correct but A is not correct. To configure OSPF, we need a wildcard in the "network" statement, not a subnet mask. We also need to assgin an area to this process – E is correct.

Which type of EIGRP route entry describes a feasible successor?

A.    a backup route, stored in the routing table
B.    a primary route, stored in the routing table
C.    a backup route, stored in the topology table
D.    a primary route, stored in the topology table

Answer: C
Feasible Successors
A destination entry is moved from the topology table to the routing table when there is a feasible successor. All minimum cost paths to the destination form a set. From this set, the neighbors that have an advertised metric less than the current routing table metric are considered feasible successors.
Feasible successors are viewed by a router as neighbors that are downstream with respect to the destination.
These neighbors and the associated metrics are placed in the forwarding table.
When a neighbor changes the metric it has been advertising or a topology change occurs in the network, the set of feasible successors may have to be re-evaluated. However, this is not categorized as a route recomputation.
Feasible successor is a route whose Advertised Distance (AD) is less than the Feasible Distance (FD) of the current best path. A feasible successor is a backup route, which is not stored in the routing table but, stored in the topology table.

Drag and Drop Question
Drag each description on the left to the appropriate term on the right. Not all the descriptions are used.

Drag and Drop Question
Drag the term on the left to its definition on the right (Not all options are used.)
Poison reverse: A router learns from its neighbor that a route is down and the router sends an update back to the neighbor with an infinite metric to that routeLSA: The packets flooded when a topology change occurs, causing network routers to update their topological databases and recalculate routes
Split horizon: This prevents sending information about a routeback out the same interface that originally learned about the route holddown timer: For a given period, this causes the router to ignore any updates with poorer metrics to a lost network

Drag and Drop Question
Drat the description on the left to the routing protocol on the right. (Not all options are used.)

Drag and Drop Question
Drat the Frame Relay acronym on the left to match its definition on the right. (Not all acronyms are used)
Enhanced Interior Gateway Routing Protocol (EIGRP) is a Cisco proprietary routing protocol, so it is vendor-specific. By default, EIGRP internal routes have an administrative distance value of 90. OSPF uses cost as its metric. By default, the cost of an interface is calculated based on bandwidth with the formula cost= 10000 0000/bandwidth (in bps). OSPF elects a DR on each broadcast and nonbroadcast multiaccess networks (like Ethernet and Frame Relay environments, respectively). It doesn’t elect a DR on point-to-point link (like a serial WAN).

Hotspot Question
OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?

A.    2
B.    3
C.    4
D.    5
E.    6
F.    7

Answer: C
It already knows about its directly connected ones, only those not directly connected are "Learned by OSPF".
OSPF as a link state routing protocol (deals with LSAs rather than routes) does not auto summarize (doesn’t support "auto-summary").So learned route by OSPF are followed

Hotspot Question
After the network has converged, what type of messaging, if any, occurs between R3 and R4?

A.    No messages are exchanged.
B.    Hellos are sent every 10 seconds.
C.    The full database from each router is sent every 30 seconds.
D.    The routing table from each router is sent every 60 seconds.

Answer: B
HELLO messages are used to maintain adjacent neighbors so even when the network is converged, hellos are still exchanged. On broadcast and point-to-point links, the default is 10 seconds, on NBMA the default is 30 seconds.

Hotspot Question
To allow or prevent load balancing to network, which of the following commands could be used in R2? (Choose two.)

A.    R2(config-if)#clock rate
B.    R2(config-if)#bandwidth
C.    R2(config-if)#ip ospf cost
D.    R2(config-if)#ip ospf priority
E.    R2(config-router)#distance ospf

Answer: BC
The cost (also called metric) of an interface in OSPF is an indication of the overhead required to send packets across a certain interface. The cost of an interface is inversely proportional to the bandwidth of that interface. A higher bandwidth indicates a lower cost. There is more overhead (higher cost) and time delays involved in crossing a 56k serial line than crossing a 10M ethernet line. The formula used to calculate the cost is:
cost= 10000 0000/bandwith in bps
For example, it will cost 10 EXP8/10 EXP7 = 10 to cross a 10M Ethernet line and will cost 10 EXP8/1544000 =64 to cross a T1 line.
By default, the cost of an interface is calculated based on the bandwidth; you can force the cost of an interface with the ip ospf cost <value> interface subconfiguration mode command.

Lead2pass helps millions of candidates pass the Cisco 200-105 exam and get the certification. We have tens of thousands of successful stories. Our dumps are reliable, affordable, updated and of really best quality to overcome the difficulties of Cisco 200-105 certifications. Lead2pass exam dumps are latest updated in highly outclass manner on regular basis and material is released periodically.

200-105 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDY2V1UExCV21ZUHM

2016 Cisco 200-105 exam dumps (All 346 Q&As) from Lead2pass:

http://www.lead2pass.com/200-105.html [100% Exam Pass Guaranteed]


Why Choose Lead2pass?

If you want to pass the exam successfully in first attempt you have to choose the best IT study material provider, in my opinion, Lead2pass is one of the best way to prepare for the exam.

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back

Comments are closed.